Sikafloor®-269 ECF CR
Sikafloor®-269 ECF CR is a two part, total solid, electrostatic conductive, low particle and ultra-low VOC/AMC emission, self-smoothing epoxy resin for floor covering designed for cleanroom environments. "Total solid epoxy composition acc. to the test method Deutsche Bauchemie e.V. (German Association for construction chemicals)". Sikafloor®-269 ECF CR is the main wearing course of the Sikafloor® Multidur ES-28 ECF/EQ System.
- Ultra-low VOC/AMC emissions
- Low particle emissions
- Organo phosphate and phthalate free
- Good chemical and mechanical resistance
- Electrostatic conductive system
- Easy to clean
- Economical
- Liquid proof
- Total solid
- Gloss finish
Usage
- Especially designed for the use in cleanroom environments, where ultra-low VOC/AMC and particle emissions are mandatory, such as optical goods, medical or space industry.
- Also suitable as a hard wearing course for many industries, such as automotive, pharmaceutical, storage facilities and warehouses.
Advantages
- Ultra-low VOC/AMC emissions
- Low particle emissions
- Organo phosphate and phthalate free
- Good chemical and mechanical resistance
- Electrostatic conductive system
- Easy to clean
- Economical
- Liquid proof
- Total solid
- Gloss finish
Packaging
Part A | 24,9 kg containers |
Part B | 5,1 kg containers |
Part A+B | 30 kg ready to mix units |
Colour
Resin - part A | coloured, liquid |
Hardener - part B | transparent, liquid |
Almost unlimited choice of colour shades.
Due to the nature of carbon fibres providing the conductivity, it is not possible to achieve exact colour matching. With very bright colours (such as yellow and orange), this effect is increased. Under direct sun light there may be some discolouration and colour variation, this has no influence on the function and performance of the coating.
Product Details
ENVIRONMENTAL INFORMATION
LEED Rating
Sikafloor®-269 ECF CR conforms to the requirements of LEED EQ Credit 4.2: Low-Emitting Materials: Paints & Coatings SCAQMD Method 304-91 VOC Content < 100 g/l.
APPROVALS / STANDARDS
- Synthetic resin screed material according to EN 13813:2002, Declaration of Performance 02 08 01 02 045 0 000008 2017, certified by Factory Production Control Body No. 0921, certificate 2017, and provided with the CE marking
- Coating for surface protection of concrete according to EN 1504-2:2004, Declaration of Performance 02 08 01 02 045 0 000008 2017, certified by Factory Production Control Body No. 0921, certificate 2017, and provided with the CE marking
- Particle emission certificate Sikafloor®-269 ECF CR CSM Statement of Qualification - ISO 14644-1, class 4 - Report No. SI 0908-494 and GMP class A, Report No. SI1008-533.
- Outgassing emission certificate Sikafloor-269 ECF CR: CSM Statement of Qualification - ISO 14644-8, class -9.6 - Report No. SI 0908-494.
- Biological Resistance in accordance with ISO 846, CSM Report No. SI 1008-533.
- Fire classification in accordance with EN 13501-1, Report-No. 2009-1823 K1, Bodycoat Frankfurt, Germany, August 2009.
- Outgassing Datasheet Sikafloor®-269 ECF CR (+90°C), M+W Group, 13.05.2009.
Chemical Base
Epoxy
Shelf Life
24 months from date of production
Storage Conditions
The packaging must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5°C and +30°C.
Density
Part A | ~ 1.7 kg/l |
Part B | ~ 1.0 kg/l |
Mixed resin | ~ 1.5 kg/l |
All Density values at +23°C
Solid content by weight
~100 %
Solid content by volume
~100 %
Shore D Hardness
~84 (14 days / +23°C) | (DIN 53 505) |
Abrasion Resistance
Resin (filled): ~ 50 mg (CS 10/1000/1000) (14 days / +23°C) | (EN ISO 5470-1 (Taber Abraser Test)) |
Compressive Strength
Resin (filled with Sikafloor® Filler 1): ~ 100 N/mm² (28 days/+23°C) | (EN 13892-2) |
Tensile Strength in Flexure
Resin (filled with Sikafloor® Filler 1): ~ 44 N/mm² (28 days/+23°C) | (EN 13892-2) |
Tensile Adhesion Strength
> 1.5 N/mm² (failure in concrete) | (ISO 4624) |
Chemical Resistance
Resistant to many chemicals. Please contact Sika technical service.
Thermal Resistance
Exposure* | Dry heat |
Short-term max. 7 d | +50°C |
Short-term moist/wet heat* up to +80°C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Electrostatic Behaviour
Resistance to ground1) | Rg < 109 Ω |
Typical average resistance to ground2) | Rg < 106 Ω |
1) This product fulfils the requirements of ATEX 137
2) Readings may vary, depending on ambient conditions (i.e. temperature, humidity) and measurement equipment.
Application
Mixing Ratio
Part A : part B = 83: 17 (by weight)
Ambient Air Temperature
+15°C min. / +30°C max.
Relative Air Humidity
80% r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+15°C min. / +30°C max.
Substrate Moisture Content
< 4% pbw moisture content. Test method: Sika®-Tramex meter, CM-measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperatures | Time |
+15°C | ~ 45 minutes |
+20°C | ~ 30 minutes |
+30°C | ~ 15 minutes |
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+15°C | ~ 72 hours | ~ 7 days | ~ 21 days |
+20°C | ~ 48 hours | ~ 4 days | ~ 7 days |
+30°C | ~ 24 hours | ~ 2 days | ~ 5 days |
Note: Times are approximate and will be affected by changing ambient conditions.
Consumption
Self-smoothing wearing course (Film thickness ~ 1.5 mm) | Sikafloor®-269 ECF CR filled with Sikadur® 501 IN | Maximum 2.0 kg/m² Binder + Sikadur® 501 IN. Depending on the temperature the filling grade varies from: 1 : 0.1 pbw (1.8 + 0.2 kg/m²) 1 : 0.2 pbw (1.6 + 0.4 kg/m²) |
These figures are theoretical and does not allow for any additional material required due to surface porosity, surface profile, variations in level and wastage etc.
For further details please refer to the system related System Data Sheet.
MIXING
Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved. When parts A and B have been mixed, add Sikadur® 501 IN and mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment. Sikafloor®-269 ECF CR must be thoroughly mixed using a low speed electric stirrer (300 - 400 rpm) or other suitable equipment.
APPLICATION
Sikafloor®-269 ECF CR is poured, spread evenly by means of a serrated trowel e.g. Large-Surface Scraper No. 656, Toothed blades No. 25 (www.polyplan.com). After spreading the material evenly, turn the serrated trowel and smooth the surface in order to achieve an aesthetically higher grade of finish. Roll immediately (within max. 10 minutes of application) in two directions with a steel spiked roller to ensure even thickness and to remove entrapped air. To obtain the highest level of aesthetic finish, spike roll in two directions at a 90 degree angle, passing only once in each direction.
CLEANING OF TOOLS
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.