Product Data Sheet Show all documents

Sikafloor®-619

Low viscosity epoxy impregnation

Sikafloor®-619 is a two part very low viscosity, solvent containing epoxy impregnation material. When brushed or rolled over cured concrete, Sikafloor®-619 impregnates the concrete to provide a surface with increased hardness and resistance to moisture penetration.

  • Easy to mix
  • Low viscosity for deep penetration (viscosity close to that of water)
  • Fast application
  • Reduces dusting and thus, easier cleaning of slabs
  • Increased resistance to abrasion and mild chemicals
  • Enhanced resistance to oils, gasoline, kerosene and staining from spillage.
  • Increased impermeability of concrete and reduces rate of penetration of waterborne contaminants such as chlorides
  • Sikafloor®-619 is not a coating, therefore it will not peel or flake off
Product Data Sheet Show all documents

Usage

Sikafloor®-619 can be used as a sealer and surface hardener for cementitious floors/surface in:
  • Plant rooms
  • Warehouse and workshop floors
 

Advantages

  • Easy to mix
  • Low viscosity for deep penetration (viscosity close to that of water)
  • Fast application
  • Reduces dusting and thus, easier cleaning of slabs
  • Increased resistance to abrasion and mild chemicals
  • Enhanced resistance to oils, gasoline, kerosene and staining from spillage.
  • Increased impermeability of concrete and reduces rate of penetration of waterborne contaminants such as chlorides
  • Sikafloor®-619 is not a coating, therefore it will not peel or flake off

Packaging

Part A

0.9 kg x 4 containers

Part B

0.9 kg x 4 containers

Part A + Part B

1.8 kg ready to mix units

Product Details

Product Information

Chemical Base

Epoxy

Shelf Life

12 months from the date of production if stored properly in original, unopened and undamaged sealed packaging

Storage Conditions

Store properly in dry conditions at temperatures between between +5 °C and +30 °C. Keep away from direct sunlight.

Density

Part A + B

0.94–0.96 kg/l (at +28 °C)

Solid content by weight

26%

Viscosity

Part A + B

40–90 cps (at +28 °C)
Technical Information

Tensile Adhesion Strength

> 1.5 N/mm² (failure at concrete)

(ASTM C 1583)

Application

Application Information

Mixing Ratio

Part A : Part B = 1 : 1 (by volume)

Relative Air Humidity

80 % max.

Dew Point

Beware of condensation!

The substrate must be at least 3 °C above the dew point to reduce the risk of condensation.

Pot Life

~60 minutes (at +28 °C)

At higher temperature the pot life is reduced.

Waiting Time / Overcoating

Temperature

Minimum

Maximum

+16 °C

10 hours

36 hours

+24 °C

6 hours

24 hours

+32 °C

4 hours

18 hours

Applied Product Ready for Use

At +25 °C:

Tack free

Foot traffic

Light traffic

Full cure

2–6 hours

24 hours

3 days

5–7 days
Consumption

Consumption

Porous concrete

min. 3 coats

~0.2 kg/m²/coat

Normal concrete and dense concrete

min. 2 coats

~0.2 kg/m²/coat
Application steps

MIXING

Pour Part B into the Part A container and mix both liquid thoroughly for one minute using a mixing paddle attached to an electric stirrer (< 500 rpm), until a fully homogeneous mix has been achieved. Decant the whole mix into another container and mix for another 30 seconds. Sikafloor®-619 is now ready to be applied.

APPLICATION

Horizontal Surface

Pour and spread Sikafloor®-619 evenly onto the prepared substrate by means of a squeegee and then backroll (cross-wise) using a short-piled roller. Avoid the formation of puddles. Apply as much material as the surface will absorb without leaving any excess material on the surface. The correct application rate will depend very much on the porosity of the concrete and should be determined on a small test area prior to large scale application.

The second coat shall be applied in the same way. For the waiting time between coats please refer to the overcoating table. A third coat may be necessary to give the required in-surface seal on porous substrates but on typical good quality dense concrete, two coats will normally be adequate.

It is important that the area is well ventilated to allow sufficient evaporation of the solvent, particularly at low application temperatures.

Vertical Surface

Sikafloor®-619 can be applied using a brush or roller.

CLEANING OF TOOLS

Clean all tools and application equipment with thinner immediately after use. Hardened or cured material can only be removed mechanically.

CLEANING

Clean regularly using a single or double headed rotary scubber drier with alkaline detergent.

Documents