Sikadur®-42 MP IN
3-part multipurpose epoxy grouting system
Sikadur®-42 MP IN is a three component, multipurpose, solvent-free, moisture tolerant epoxy grouting system. For use at temperature between +25°C and +40°C.
- High early strength
- Ready to mix pre batched units
- Moisture tolerant
- Non-shrink
- Corrosion and chemically resistant
- High compressive strength
- High vibration resistance
- Low coefficient of thermal expansion
Usage
High-strength grouting and fixing of :- Starter bars
- Anchors
- Fasteners
- Tie rods
- Crash barrier posts
- Base plates
- Machine bases, seat base-plates for light and heavy machinery including heavy impact and vibratory machinery, reciprocating engines compressors, pumps, presses etc.
- Bridge bearings
- Mechanical joints (i.e. road / bridge / deck types etc.)
- Crane tracks
- Light rail and permanent way in tunnels
- Light rail and permanent way over bridges
Advantages
- High early strength
- Ready to mix pre batched units
- Moisture tolerant
- Non-shrink
- Corrosion and chemically resistant
- High compressive strength
- High vibration resistance
- Low coefficient of thermal expansion
Packaging
| Pre-batched unit A+B+C | 21.6 kg x 2 sets |
| Part A | 3.00 kg plastic container |
| Part B | 0.60 kg metal container |
| Part C | 18.00 kg bag |
Colour
| Part A | hazy |
| Part B | reddish yellow |
| Part C | grey |
| Part A+B+C mixed | grey |
Product Details
Chemical Base
Epoxy resin
Shelf Life
12 months from date of production
Storage Conditions
Store properly in original unopened, sealed and undamaged packaging, in dry conditions at temperatures between +20°C and +40°C. Protect from direct sunshine.
Density
Part A+B+C mixed : 2.2 ± 0.1 kg/liter (at +30°C)
Compressive Strength
| 1 day | ≥ 75 N/mm2 |
| 3 days | ≥ 80 N/mm2 |
| 7 days | ≥ 90 N/mm2 |
| 14 days | ≥ 95 N/mm2 |
Curing Temperature +30°C
Effective Bearing Area
| > 85% | (ASTM C 1339) |
Tensile Strength in Flexure
| ≥ 25 N/mm2 (after 7 days at +30°C) | (ISO EN 196) |
Tensile Strength
| ≥ 10 N/mm2 (after 7 days at +30°C) | (ASTM D 638) |
Tensile Adhesion Strength
| ≥ 10 N/mm2, concrete failure (after 7 days at +30°C) | (ASTM C 882) |
Heat Deflection Temperature
| +55°C (7 days / +30°C) | (ASTM D 648) |
Water Absorption
< 1%
Application
Mixing Ratio
Part A : B : C = 5 : 1 : 30 (by weight)
Layer Thickness
| Minimum grout depth | 25 mm |
| Maximum grout depth | 125 mm |
Peak Exotherm
| ~ 42°C (at +30°C) | (ASTM D 2471) |
Product Temperature
+20°C min. / +40°C max.
Ambient Air Temperature
+5°C min. / +35°C max
Dew Point
Beware of condensation !
Substrate temperature during application must be at least 3°C above dew point to avoid condensation.
Substrate Temperature
+5°C min. / +35°C max
Pot Life
| ~ 45 minutes (100 g mass at +30°C) | (FIP 5.1) |
The pot life begins when the resin and hardener are mixed. It is shorter at high temperatures and longer at low temperatures. The greater the quantity mixed, the shorter the pot life. To obtain longer workability at high temperatures, the mixed adhesive may be divided into portions. Another method is to chill parts A+B and C before mixing them (i.e. only when application temperatures are above +20°C).
Consumption
~ 2200 kg/m3
SUBSTRATE QUALITY
Mortar and concrete must be older than 28 days (dependent on minimum strength requirements).Verify the substrate strength (concrete, masonry, natural stone). The substrate surface (all types) must be clean and free from contaminants such as dirt, oil, grease, existing surface treatments and coatings etc. Steel substrates must be de-rusted and cleaned. The substrate must be sound and all loose particles must be removed. Substrate must be dry or mat damp and free from any standing water, ice etc.
SUBSTRATE PREPARATION
Concrete / mortar / stone / bricks
Substrates must be sound, clean and free from laitance, grease, oils, old surface treatments or coatings and all loose or friable particles must be removed to achieve a laitance and contaminant free, open textured surface.
Steel
Must be cleaned and prepared thoroughly to an acceptable quality i.e. by blast cleaning and vacuum. Avoid dew point conditions.
Surface and base plate contact area must be clean and sound. For best results, the substrate shall be dry. Remove dust, laitance, oils, grease, curing compounds, impregnations, waxes, foreign particles, coatings, and disintegrated materials by mechanical means, i.e. chipping with a chisel, blastcleaning etc. All anchor pockets or sleeves must be free of water. Apply grout immediately to prevent re-oxidizing / rust
formation.
MIXING
Pre-batched units
Mix components A and B in the component A pail for approx. 30-60 seconds with a paddle type mixer to a low speed drill (300-450 rpm). Avoid aeration while mixing until the material becomes uniformly blended in colour and viscosity. Place the mixed epoxy into an appropriate mixing vessel. Slowly add the contents of component C (to keep air entrapment at a minimum) dependent on flow requirements (observe the correct mixing ratio) and mix until uniform and homogeneous (approx. 3 min).
Mix only that quantity which can be used within its potlife.
When using multiple units, one after the other. Do not mix the following unit until the previous one has been used in order to avoid a reduction in handling time.
CLEANING OF TOOLS
Clean all tools and application equipment with Sika® Colma Cleaner immediately after use. Hardened / cured material can only be mechanically removed.